Wadjay 1500mm metal sheet embossing machine for stainless, aluminum, galvanized and cold-rolled plate: cold roller embossing, custom pattern rollers, hydraulic pressure adjust, PLC control. Anti-slip checker/stucco sheets. Quote.CE/ISO
Why Choose a 1500mm Metal Sheet Embossing Machine?
A metal sheet embossing machine uses matched upper/lower pattern rollers to press a permanent 3D texture into metal plate at room temperature — no heating, no coating damage. For buyers making anti-slip floor plates, stair treads, truck beds, elevator panels, appliance skins or architectural façade sheets, the value is three-fold: pattern consistency across coil width, higher surface rigidity than flat sheet, and one line instead of manual stamping. metal sheet embossing machine
The Wadjay 1500mm plate embossing line targets mid-width coil/sheet processing — galvanized steel, color steel, cold-rolled steel, aluminum and stainless plate. Pattern rollers are changeable, so diamond checker, stucco (orange peel), wood grain, leather or custom OEM textures run on the same frame. Typical flow: decoiler → entry guide → leveling → embossing rollers → run-out table, with hydraulic pressure and roller gap adjusted per material thickness. metal sheet embossing machine
| Item | This page / Wadjay config |
|---|---|
| Working width | 1500mm（per product title；wider/narrower roller by quote） |
| Process | Cold roller embossing, upper + lower male/female rollers |
| Material | Stainless steel, aluminum, galvanized, color steel, cold-rolled steel |
| Thickness range | Confirm per pattern — light decorative 0.3–0.8mm / medium 0.8–1.5mm / heavy plate 1.5–3mm+ |
| Embossing roller | Replaceable pattern roller; custom by sample/DXF |
| Pressure system | Hydraulic pressure adjust（tonnage by material/thickness） |
| Gap control | Screw / turbine reducer / hydraulic cylinder（configurable） |
| Drive | Gear transmission + inverter motor + PLC control |
| Speed | Set by thickness & pattern depth；typical embossing 10–20 m/min for thin plate |
| Leveling / exit | Entry leveling + run-out table optional in line |
| Pattern types | Diamond checker, stucco, teardrop, wood grain, leather, custom |
| Voltage / HMI | 380V/50Hz/3-phase standard；other voltage & language configurable |
| Certification | ISO configurable；CE by destination |
| Warranty / test | Pre-shipment running video；warranty per order scope |
Not fixed on this page（quote separately）
- Motor power 11kW / 15kW / 30kW+ → depends on width & thickness
- Roller Ø 380–500mm, 42CrMo/60CrMnMo, HRC 58–62 → by pattern load
- Hydraulic tonnage 50–100T or higher → by plate gauge
- Pattern depth tolerance / COF grade → only with FAT report
How the Embossing Line Works（Expertise） metal sheet embossing machine
- Decoiling / sheet feed — coil or plate enters through guide to avoid side drift.
- Leveling — light correction before rollers so pattern depth stays uniform across 1500mm width.
- Roller engagement — upper embossing roller + lower matching roller press the surface; metal undergoes cold plastic deformation.
- Pressure & gap setting — hydraulic unit or screw reducer sets tonnage; gap matched to thickness to avoid over-press crack or shallow impression.
- Pattern transfer — engraved roller surface replicates diamond/stucco/custom texture continuously.
- Run-out / recoil — embossed sheet goes to table or re-coiler; inspect pattern depth at edges + center.
- Roller change — for new pattern, swap roller set; same frame reused.
Application Scenarios
- Industrial anti-slip plate — factory mezzanine, walkways, machine surrounds
- Stair treads & ramps — diamond checker plate for warehouses/docks
- Truck / trailer / bus — floor plates, running boards, cargo beds
- Marine & offshore — aluminum/stainless deck plate, gangways
- Food & pharma — stainless anti-slip floors, washdown stairs
- Architecture & decoration — embossed façade, ceiling, elevator cabin, stainless water-ripple wall
- Home appliance / HVAC — refrigerator door, washer panel, duct skin
Why Wadjay 1500mm Embossing Line
- 1500mm mid-width plate — covers standard architectural/industrial sheet sizes
- Cold roller process — no heat damage to galvanized/pre-painted coating
- Replaceable pattern rollers — diamond/stucco/wood/custom OEM on one frame
- Hydraulic pressure adjust — stable emboss depth on stainless vs aluminum
- PLC + inverter — speed/pressure preset, fault diagnostics
- Multi-material — SS/aluminum/galvanized/cold-rolled in one line
- ISO + CE-configurable — export voltage/HMI language supported
- Pre-shipment video — empty run + material test on request
E-E-A-T Trust Block
- Experience：Wadjay configures embossing roller by customer sample; test run checks pattern alignment edge-to-center, surface marking, coil tracking before container load.
- Expertise：Specs written against product page（1500mm embossing line）+ cold-roller embossing process; speed/pressure/thickness confirmed per material.
- Authoritativeness：Henan Wadjay Machinery export catalog；related roll forming/slitting/leveling lines；ISO/CE configurable.
- Trust：No “#1/best/±0.02mm” claims without FAT data. Price, motor power, roller hardness, lead time confirmed per profile.
FAQs
Q1: What width does this machine handle?
A: Product line is 1500mm working width. Narrower rollers (1000–1300mm) or wider up to 1600–2000mm quoted separately.
Q2: What materials can be embossed?
A: Stainless, aluminum, galvanized, color steel, cold-rolled steel. Thickness range confirmed by pattern depth and yield.
Q3: What patterns are supported?
A: Diamond checker, stucco/orange peel, teardrop, wood grain, leather, custom logo/textured roller by sample or DXF.
Q4: Hydraulic or mechanical pressure?
A: Standard line uses hydraulic pressure adjust; screw/turbine gap control available on lighter configs.
Q5: Does it damage galvanized or pre-painted coating?
A: Cold roller embossing at correct gap/pressure does not heat the strip; coating marks come from over-pressure or dirty rollers — set gap per thickness.
Q6: How fast is it?
A: Depends on thickness and pattern depth. Thin decorative plate runs higher line speed; heavy checker plate slower. Don’t quote one fixed m/min without material sample.
Q7: Roller material and hardness?
A: Typically 42CrMo / 60CrMnMo forged roller, surface hardened HRC 58–62 on similar industrial embossing machines — confirm per Wadjay offer.
Q8: CE / ISO / warranty?
A: ISO configurable; CE by destination. Warranty and FAT report per order scope.
Q9: How to quote?
A: Send base material（SS304/aluminum 5052/galvanized）, thickness, coil/sheet width, pattern sample or drawing, target speed, voltage/Hz, destination. Wadjay returns roller plan + pressure config + price.