Wadjay 1500mm metal sheet embossing machine for stainless, aluminum, galvanized and cold-rolled plate: cold roller embossing, custom pattern rollers, adjustable pressure, PLC control. Anti-slip checker/stucco sheets. CE/ISO. Quote.
Why Choose a 1500mm Metal Sheet Embossing Machine?
A metal sheet embossing machine uses matched upper/lower pattern rollers to press a permanent 3D texture into metal plate at room temperature — no heating, no coating damage. For buyers making anti-slip floor plates, stair treads, truck beds, elevator panels, appliance skins or architectural façade sheets, the value is three-fold: pattern consistency across coil width, higher surface rigidity than flat sheet, and one line instead of manual stamping.
The Wadjay 1500mm plate embossing line targets mid-width coil/sheet processing — galvanized steel, color steel, cold-rolled steel, aluminum and stainless plate. Pattern rollers are changeable, so diamond checker, stucco (orange peel), wood grain, leather or custom OEM textures run on the same frame. Typical flow: decoiler → entry guide → leveling → embossing rollers → run-out table, with pressure and roller gap adjusted per material thickness.
| Item | This page / Wadjay config |
|---|---|
| Working width | 1500mm（per product title；narrower 1000–1300mm or wider 1600–2000mm quoted separately） |
| Process | Cold roller embossing, upper + lower male/female rollers |
| Material | Stainless steel, aluminum, galvanized, color steel, cold-rolled steel |
| Thickness range | Confirm per pattern — decorative 0.3–0.8mm / medium 0.8–1.5mm / heavy plate up to 3mm |
| Embossing roller | Replaceable pattern roller; custom by sample/DXF |
| Pressure system | Hydraulic pressure adjust or screw/turbine reducer（configurable） |
| Drive | Gear transmission + inverter motor + PLC control |
| Speed | Set by thickness & pattern depth；similar 1500mm lines reference 0–30m/min，thin decorative faster |
| Leveling / exit | Entry leveling + run-out table optional in line |
| Pattern types | Diamond checker, stucco, teardrop, wood grain, leather, custom logo |
| Voltage / HMI | 380V/50Hz/3-phase standard；other voltage & language configurable |
| Certification | ISO configurable；CE by destination |
| Warranty / test | Video technical support；warranty per order scope |
How the Embossing Line Works（Expertise） metal sheet embossing machine
- Decoiling / sheet feed — coil or plate enters through guide to avoid side drift.
- Leveling — light correction before rollers so pattern depth stays uniform across 1500mm width.
- Roller engagement — upper embossing roller + lower matching roller press the surface; metal undergoes cold plastic deformation.
- Pressure & gap setting — hydraulic unit or screw reducer sets tonnage; gap matched to thickness to avoid over-press crack or shallow impression.
- Pattern transfer — engraved roller surface replicates diamond/stucco/custom texture continuously.
- Run-out / recoil — embossed sheet goes to table or re-coiler; inspect pattern depth at edges + center.
- Roller change — for new pattern, swap roller set; same frame reused.
Why Wadjay 1500mm Embossing Line metal sheet embossing machine
- 1500mm mid-width plate — covers standard architectural/industrial sheet sizes
- Cold roller process — no heat damage to galvanized/pre-painted coating
- Replaceable pattern rollers — diamond/stucco/wood/custom OEM on one frame
- Adjustable pressure — stable emboss depth on stainless vs aluminum
- PLC + inverter — speed/pressure preset, fault diagnostics
- Multi-material — SS/aluminum/galvanized/cold-rolled in one line
- ISO + CE-configurable — export voltage/HMI language supported
- Pre-shipment video — empty run + material test on request
FAQs
Q1: What width does this machine handle?
A: Product line is 1500mm working width. Narrower rollers (1000–1300mm) or wider up to 1600–2000mm quoted separately.
Q2: What materials can be embossed?
A: Stainless, aluminum, galvanized, color steel, cold-rolled steel. Thickness range confirmed by pattern depth and yield.
Q3: What patterns are supported?
A: Diamond checker, stucco/orange peel, teardrop, wood grain, leather, custom logo/textured roller by sample or DXF.
Q4: Hydraulic or mechanical pressure?
A: Standard line uses hydraulic pressure adjust; screw/turbine gap control available on lighter configs.
Q5: Does it damage galvanized or pre-painted coating?
A: Cold roller embossing at correct gap/pressure does not heat the strip; coating marks come from over-pressure or dirty rollers — set gap per thickness.
Q6: How fast is it?
A: Depends on thickness and pattern depth. Thin decorative plate runs higher line speed; heavy checker plate slower. Don’t quote one fixed m/min without material sample.
Q7: Roller material and hardness?
A: Typically 42CrMo / 60CrMnMo forged roller, surface hardened HRC 55–60 on similar industrial embossing machines — confirm per Wadjay offer.
Q8: CE / ISO / warranty?
A: ISO configurable; CE by destination. Warranty and FAT report per order scope.
Q9: How to quote?
A: Send base material（SS304/aluminum 5052/galvanized）, thickness, coil/sheet width, pattern sample or drawing, target speed, voltage/Hz, destination. Wadjay returns roller plan + pressure config + price.